Impact stone crushers machine use of impact on broke material. When it working, the rotor highspeed rotation with the motordriven. The material into the crusher machine, impact the rotor plate hammer and broken. Then it is back to the lining plate broken again, finally discharged from the discharge port.
® NP1110™ HSI crusher is the smallest model in ® NP Series™ HSI crushers family and available as a stationary unit or mobile version. High performance . ® NP1110™ HSI crusher consists of heavy rotor, wear resistant materials, and an optimal crusher chamber design.
· Here, we mainly introduce parameters in impact crusher that affects its function. 1. Diameter And Length Of Rotor. Generally, the diameter and length of rotor is related with the feeding size of raw material. While crushing the raw materials, we need enough impact force. In other words, the diameter and length of rotor should be proper.
Built Rotors. New Vs. Rebuilt Rotors. RQI, Inc. manufactures rotors and rotor parts for use in a specific style of rock crushing machine called an Impact Crusher, or an Impactor. Impactors use high speed collisions between the rock and both moving and stationary bars inside the .
Crusher Frame: Upper and Lower crusher frames constructed of 3/4"steel plate. Replaceable 1 ¼" wear resistant alloy steel frame liners. (Two) hydraulic cylinders for opening upper frame. (with hydraulic pump) (Two) safety pins to hold upper frame open during maintenance. Rotor pin and holder to keep rotor from rotating during service.
· Impact crushing can be of two variations: gravity and dynamic. An example of gravity impact would be dropping a rock onto a steel plate (similar to what goes on into an Autogenous Mill). Dynamic impact could be described as material dropping into a rapidly turning rotor where it receives a smashing blow from a hammer or impeller.
Rotor. The rotor is mounted on a vertical shaft. The material stream first connects with a distribution cone. Below this, the rotor has two levels, each of which can be fitted with a maximum of two pivotmounted hammers. Crushing is carried out primarily between the rotating hammers and the stator strips on the machine casing.
Mobile Impact crushing plant The main engine of Shanghai mobile impact crushing station adopts the unique design of heavy rotor, large capacity crushing chamber, thick counterattack plate, high alloy wearresisting plate hammer, hydraulic opening device and so on, so that it has the characteristics of large crushing capacity and crushing ratio, stable quality, low production cost and ...
· To meet these challenges, the company has developed its new Orange Series Rotor for vertical shaft impact (VSI) crushers. With the new rotors, states that productive uptime can be increased substantially through longer parts lifetime and faster service. VSIs are widely used in mines, especially as tertiary or quaternary stage crushers.
OPERATING DIMENSIONS TRANSPORT DIMENSIONS • • 4043T Impact Crusher Specifiions CRUSHER • 40" diameter rotor x 43" wide (1,016mm x 1,092mm) impact crusher • Lid Crusher Relief System™ with 6" (152mm) raise feature • Feed inlet opening: 43" wide x 28" high (1,092mm x 711mm) • 2 adjustable curtains (apron .
Tertiary Impact Crusher – HAZEMAG is the specialist +49 2594 77 0 +49 2594 77 400 HAZEMAG EPR Brokweg 75 · 48249 Dülmen, Germany info Rotors The rotor of the Impact Crusher is generally the most stressed component during the crushing procedure. Depending on the crushing problem to be solved, two
The CRH1316 HSI plant is tough to match in productivity. This portable plant features the Cedarapids IP1316 impact crusher, with its massive rotor, quick change impact bars, and heavy monoblock primary curtain, all designed for years of tough primary crushing.
Rotor unbalance: After a period of time, due to some reasons caused by rotor unbalance, it will cause the machine vibrate abnormal, in this case, need to adjust the rotor. 4. The foundation is loose: When the impact crusher is installed, the foundation is not fixed, or in the process of use, the machine is shaking caused by the loosening of the anchor bolt.
Impact crushers (also known as impactors or horizontal shaft impactors) can be used in primary, secondary, or tertiary appliions. They use inertia of the blowbars fitted to the rotor to fracture the material, resulting in a high reduction ratio.
KLEEMANN impact crushers are equipped with different rotors depending on the size of the crusher and the appliion. The number of builtin blow bars primarily depends on the crush ing chamber geometry and its associated intake behaviour. For smaller crushing chamber geometries (inlet width of un der 1,100 mm with rotor diameter under 1,100 ...
The Finlay I110 tracked mobile impact crusher has been specifically designed for quarrying, mining, recycling and demolition appliions. The Finlay I110 features a 1000mm x 1000mm (40" x 40") hydrostatic drive impact chamber with variable speed offering. Learn more now.
The HPI Series Primary Impact Crusher is ideally suited to crush run of quarry, mediumhard materials down to a product size of 0 – 8 inch (90% 4") in a single pass. This machine is normally offered within a plant/system where secondary crushing is also present. However, due to its high reduction ratio the need for multiple secondary units is normally eliminated.
3) IMPACT CRUSHER Type Inlet opening Weight impact crusher Rotor width Rotor diameter Drive Blow bars Rotor speed Pulley diameter Weight rotor Throughput capacity Impact aprons Gap upper apron Gap lower apron OPTION (without hoist) 49 ICR 10000 (housing made of HB 450) 770 x 960 mm (H x W)
DESCRIPTION 3 PORT ROTOR 6 PORT ROTOR OPEN ROTOR Maximum feed size 50mm 60mm 120mm Feed passing screen 40mm 45mm 75mm Rotor speed 1250 1650rpm 1250 1650rpm 900rpm Rotor diameter 1000mm 900mm *1000mm Throughput Up to 250tph through the rotor, up to 400tph using cascade system VERTICAL SHAFT IMPACT CRUSHER • Rotor options dependant on ...
Hammer Crusher Rotor Features Do the stress analysis and service life can be improved by 50. Using the special design to increase the crushing efficiency effectively and improve the output capacity by .
PFW Series Impact Crusher features heavy duty rotor design, unique hammer locking system, inte PF Impact Crusher Thousands of cases proved that PF Series Impact Crushers can not only effectively increase productivity and final product quality, but also greatly reduce the .
I4c Impact Crusher. The I4C Crusher is the latest entry into 's powerful impact crusher line. The I4C is in a class of its own, bringing the productivity of an 1125mm (″) impactor to a compact footprint for maximum power and maneuverability.
· First,impact crusher vibration 1. the material is too large, you can check the feed size. wear, indiing the need to replace the hammer back, 3. rotor imbalance, the need to adjust handled properly, need to check the anchor bolts and reinforcement.. This professional crusher blog contains crusher basics which focuses on the jaw crusher, hammer crusher, impact crusher, .
Impact Crusher Parts. The impact crusher parts mainly consist of machine body, impacting plate, plate hammer, and support and lining board. (1)The machine body is composed by upper box, lower box, back upper cover, left side wall and right side wall which are connected to be an integrated part with bolts. (2) The rotor is mainly composed of ...
Rotor Superior Rotor Design The Willpactor II Secondary Impact Crusher rotor is contoured and computer designed for maximum efficiecy. The rotor's features include: Proven, positive breaker bar holding devices with buried wedges to provide minimized wear as well as breaker bar installation, removal and indexing time.